ELECTRONIC ENCLOSURE SOLUTIONS

TEL: 01403 865486 | FAX: 01403 865487
Lincoln Binns > Category:Aluminium Enclosures

E-Case Range of Extruded Aluminium Enclosures

The E-Case Range of Extruded Aluminium Enclosures is designed specifically for the most common sizes of circuit boards. These aluminium electronic enclosures are available in a variety of standard widths (55mm, 100mm, 160mm) and can be cut to your desired length. When combined with a custom front panel, you end up with a semi-custom aluminium electronic enclosure but without the complexity and cost of our Uniobox Range.

Clip On Bracket

Posted by boxesboxes on Dec 12, 2013, Categories: Aluminium Enclosures, E-Case-Accessories, Products

0
Clip On Bracket

Clip-on Bracket

Lincoln Binns has introduced a plastic clip-on mounting bracket for the E-Case enclosure range. It is an alternative to the MTS40 type metal bracket. The main benefit of the clip-on bracket is that it can be retro-fitted by the end user. The original metal bracket was retained by end plates and therefore fitted at the production stage. Retrofitting the original bracket would involve removing the end plate and therefore potentially invalidating the product warranty. The new clip on bracket is 40mm long and made of black ABS plastic. It snaps into the dovetail feature on...

Read More

E-Case A Aluminium Electronic Enclosure

Posted by boxesboxes on Mar 7, 2012, Categories: Aluminium Enclosures, Products

1
E-Case A Aluminium Electronic...

E-Case A Aluminium Electronic Enclosure is our smallest electronics enclosure

E-Case A is a box section extruded aluminium enclosure.  It takes a 55mm wide circuit board.  Standard board lengths are 40mm, 80mm or 120mm. It is also available in non-standard lengths. Standard colours are silver anodized or black anodized (which is slightly more expensive).   The silver anodized finish has bare aluminium where the ends of the extrusion have been cut.  The black anodized finish covers the complete surface of the box. Non-standard anodised colours are also available. The circuit board can have components 18 or 20mm high (depending on orientation). Fig.1 shows...

Read More

Extruded enclosure E-Case B

Posted by boxesboxes on Mar 7, 2012, Categories: Aluminium Enclosures, Products

1
Extruded enclosure E-Case B

E-Case B is our most popular extruded enclosure

E-Case B electronic enclosure is designed for Eurocard width circuit boards. It is a box section extruded enclosure to take a 100mm wide board with board lengths 80mm, 160mm or 220mm.  It is also available in non-standard lengths. Standard colours are silver anodized or black anodized (which is slightly more expensive).   The silver anodized finish has bare aluminium where the ends of the extrusion have been cut.  The black anodized finish covers the complete surface of the box. Non-standard anodised colours are also available. The circuit board can have components 18 or 20mm high (depending...

Read More

E-Case C

Posted by boxesboxes on Mar 7, 2012, Categories: Aluminium Enclosures, Products

0
E-Case C

E-Case C is one of our aluminium electronic enclosures

E-Case C extruded electronic enclosure is designed for Eurocard width circuit boards. It is a box section aluminium electronic enclosure to take a 100mm wide board with board lengths 80mm, 160mm or 220mm. It is also available in non-standard lengths. Standard colours are silver anodized or black anodized (which is slightly more expensive). Non-standard anodised finishes are also available. The circuit board can have components 33mm high. Fig.1 shows the the pcb with maximum component height on it of 33mm. This pcb will fit in the bottom groove of the box orientated as...

Read More

E-Case D

Posted by boxesboxes on Mar 7, 2012, Categories: Aluminium Enclosures, Products

0
E-Case D

E-Case D is Lincoln Binns' largest aluminum electronic enclosure

E-Case D is a box section aluminum electronics enclosure to take a 160mm wide board with board lengths 80mm, 160mm or 220mm. It is also available in non-standard lengths. Standard colours are silver anodized or black anodized (which is slightly more expensive). Non-standard anodised finishes are also available. The circuit board can have components 40mm high. Fig.1 shows the the pcb with maximum component height on it of 40mm. This pcb will fit in the bottom groove of the box orientated as in Fig.2. The pcb slides in grooves 2mm deep down either...

Read More

E-Case End Plates

Posted by boxesboxes on Mar 29, 2011, Categories: Aluminium Enclosures, E-Case-Accessories, Products

1
E-Case End Plates

The end plates are available in three finishes: black anodized, silver (clear) anodized and natural.
Natural End Plates are anodizing grade and have a removable plastic coating on one side to prevent unwanted scratches prior to application. Silver anodized End Plates are intended as partners for the E-Case (silver) electronic enclosures and black anodized End Plates are intended as partners for E-Case (black) electronic enclosures. Order Code: E-Case A End Plates: PAN1 - Natural, End Plate A 1 off PAS1 - Silver, End Plate A 1 off PAB1 - Black, End Plate A 1 off E-Case B End Plates: PBN1 - Natural, End Plate B 1 off PBS1 -...

Read More

E-Case Bezel

Posted by boxesboxes on Mar 28, 2011, Categories: Aluminium Enclosures, E-Case-Accessories, Products

1
E-Case Bezel

Cosmetic end plate surrounds made of ABS plastic that are available in four sizes to suit the four extrusion profiles. The four end-plate mounting screws pass through the bezel, through the end-plate and into the extrusion. The screw heads are concealed by inserts which closely match the bezel. This gives a much-improved cosmetic appearance.

Application Information:
The E-Case bezels come with the four inserts attached to a sprue on the bezel. The sprue should be cut off the bezel using a sharp knife. Similarly the inserts should be cut off the sprue. Care should be taken not to leave plastic pips on...

Read More

E-Case Gaskets

Posted by boxesboxes on Mar 27, 2011, Categories: Aluminium Enclosures, E-Case-Accessories, Products

0
E-Case Gaskets

Gaskets come as a set suitable for waterproofing one aluminium enclosure. A set comprises two white silicon foam gaskets and a number of polythene washers. The washers are optionally fitted under the heads of the screws and raise the rating of the gasket set from IP65 to IP66.

Application Information:
The E-Case aluminium enclosure range was not originally designed to be waterproof. Even with a gasket seal around the edge of the profile water could enter under the heads of the screws and enter the enclosure through the open screwport. The original waterproof aluminium enclosure range was the Linc-Ace range which had...

Read More
1
E-Case Lug – Extruded...

Extruded Mounting Bracket from Lincoln Binns Ltd

Aluminium extruded mounting bracket for fixing E-Case housings to walls, panels, vehicle bulkheads etc. Linc-Lug slides into any external dovetail feature on E-Case housings and is retained by the end plates. The silver lugs are strip silver anodized and are used with the silver E-Case enclosures that are anodized in the same way. The black lugs are individually black anodized like the black boxes in the E-Case range. Order Code: LSS40 - Silver 40mm Lug 1 off LSB40 - Black 40mm Lug 1 off LSS80 - Silver 80mm Lug 1 off LSB80 - Black 80mm Lug 1 off MTS40 -...

Read More
1
E-Case Self-Tapping or Thread...

Self-Tapping and Thread-Forming Screws Are Available For The E-Case

There are two screw types for the E-Case available:
A No.4 self tapping screw, which comes with a Philips head SC8 - silver, bag of 8 off screws SC400 - silver, bag of 400 off screws SCB8 - black, bag of 8 off screws SCB400 - black, bag of 400 off screws A M3 thread-forming screw, which comes with a Torx head SCT8 - silver, bag of 8 off screws SCT400 - silver, bag of 400 off screws SCTB8 - black, bag of 8 off screws SCTB400 - black, bag of 400 off screws E...

Read More

Did you know?

We undertake design and prototyping as well as mass production.

You can also fit any size circuit board into our electronic enclosures. Either with a special carrier plate or with a custom sized UnioBox. Did you also know that there is no minimum order for boxes or panel printing. Just email us your requirements and drawings and we can quote you per unit.

Email: info@lincolnbinns.com

We can engineer your housing for you, using your circuit board and a sketch of your front panel.

Twitter Updates

Contact

Phone: 01403 865486
From abroad: +44 1403 865486

Fax: 01403 865487
From abroad: +44 1403 865487

Lincoln Binns Ltd‎
Oakendene Industrial Estate
Bolney Rd, Cowfold, Horsham, West Sussex
RH13 8AZ

Company Registration Number - 1904817
VAT number – GB 423 2273 85