Aluminium Electronic Enclosure – E-Case B Data

image_print

Data For Our E-Case B Aluminium Electronic Enclosure

Silver or black anodized aluminium extruded box section to take 100 x 80mm, 100 x 160mm or 100 x 220mm circuit boards. Slim profile for space conscious applications. This box features dovetail slots down the side that accept a Linc-Lug mounting
bracket to facilitate surface mounting. Optional gaskets allow waterproofing. The maximum height of components on a board mounted in the bottom slot is 18mm/20mm depending on orientation. One side of the box features two sets of
appearance enhancing grooves. Between the sets of grooves is a shallow (0.5mm deep) recess that could be used for a label.

This is one of a series of sections that includes E-Case A, E-Case C and E-Case D.

E-Case B Dimensions

 

Length Tolerance: Nominal length -0mm/+1mm e.g. EBS 80 is not shorter than 80mm and not longer than 81mm.
Non-Standard Lengths: Available. See separate datasheet.
Material: Aluminium 6063 T6 (HE9).
Finish: Silver anodized 5 μm thickness to BS 1615 – can be painted directly if  equired. The inside and cut ends are not anodized. Black anodized 20 μm thickness, the inside and ends are anodized.
Weight: 1.38 Kg/m
Perimeter: 316mm outside, 306mm inside.

Extrusion Order Codes:

Length Black Silver
80mm EBB 80 EBS 80
160mm EBB 160 EBS 160
220mm EBB 220 EBS 220

Screw ports: Nominal diameter 2.7mm to take a No.4 self-tapping screw with a 3mm major diameter of a type normally used for plastic. They are not suitable for ordinary self- tapping screws that have a 2.9 mm diameter with a wide tolerance. The screw ports can be threaded M3 using a thread-rolling tap, but a thread cutting tap will make a weak thread. Alternatively an M3 thread-forming screw can be used to roll its own thread.

End plate: End plate B is size 108.5 x 29.5 x 1.5mm to suit the B profile of the E-Case range of extruded enclosures. This includes both standard enclosures and non-standard lengths. The end plate is available in three finishes, black anodized, silver (clear) anodized and natural. Natural end plates are anodizing grade and have a removable plastic coating on one side to prevent unwanted scratches prior to application. Initially, natural end plates will look the same as silver anodized, but over time will become dull or corrode if used in an application without surface protection. They would be an ideal starting point if a paint or alochrom finish were required. Silver anodized end plates are intended as partners for EBS (silver) electronic enclosures and black anodized end plates are intended as partners for EBB (black) electronic enclosures.

Application Information: The end plates are made using a ‘pierce and blank’ tool and therefore have a front with rounded edges and a back with square edges. The screw holes in the end plate are symmetrical about a vertical centre line but lie closer (at 3.5mm) to the top than the bottom. This conforms to the geometry of the E-Case enclosure. They are designed to lie flush with the enclosure top and bottom and overlap the dovetails on the sides. Any Linc-lug inserted in a dovetail will be retained by the end plates.

Material of end plate: Aluminium J57S or 5251 H22

Weight of end plate: PBN 1, PBS1, PBB 1: 12g.

E-Case B Front Plate Dimensions

Size Black Silver Natural
B PBB 1 PBS 1 PBN 1

The envelope drawing shows the relationship between three things:

  1. The circuit board in the bottom slot of the enclosure.
  2. The envelope within which components must be placed.
  3. The outside of the end plate

E-Case Internal Dimensions

Accessories:

Bezel – Optional black ABS plastic bezel renders cosmetic improvement for E-Case B. It fits over the end plate and conceals the edges. Screws pass through the bezel as well as the end plate. Inserts conceal the heads of the screws. The bezel is particularly suited to concealing the edges of self-adhesive polycarbonate labels or membrane panels fitted on top of the end plate. Order Code: ZBB1

The bezel outline drawing shows the central area of the end plate (dotted line) not covered by the plastic of the bezel.

E-Case B Plastic Bezel End Dimensions

Gasket set – comprises 2 gaskets and 8 washers to optionally fit under screw heads. Washers increase rating from IP65 to IP66. Order Code: GEB1. Full details are on the E-Case Accessories datasheet.

Linc-Lugs – Silver Order Code: LSS 40 (40mm), LSS 80 (80mm);Black Order Code LSB40 (40mm), LSB80 (80mm). Full details are on the E-Case Accessories datasheet.
Screws – No.4 x 3/8” Plastite™ posi-pan self-tapping screws: Silver Order Code: SC8 (pack of 8), SC400 (pack of 400). Black Order Code: SCB8 (pack of 8), SCB400 (pack of 400).
M3 x 10 TORX™ thread-forming screws. Silver Order Code: SCT8 (pack of 8), SCT400 (pack of 400). Black Order Code: SCTB8 (pack of 8), SCTB400 (pack of 400).

Plastite™ is a trademark of Research Engineering and Manufacturing, Inc. TORX™ is a trademark of Textron Inc. Product and data subject to change without notice. User knows application and must determine fitness for purpose and appropriateness of advice verbal or written.

To download this page in a pdf format, please click here